BATR R - BATR R010

Electric coils

Rectangular - Regulated

View larger

BATR R - BATR R010

Electric coils

Rectangular - Regulated

ModBus communicating integrated regulation
Integrated thermal protections
Power from 6 to 66 kW

Application

Fits into a horizontal or vertical network of rectangular ducts.
Terminal heating or defrost.
Maximum outlet temperature 50 ° C.

Collective residential buildings

Tertiary buildings

Buildings for catering

Order online

Description
Dimensions
Documentation
Public Price
Software
References

Dimensions B x H: 400 x 200 to 1000 x 500 mm.
Power from 6 to 66 kW.
Single 230V 50Hz, three 400V 50Hz or three 400V + N 50Hz power supply from 18kW.
Communicating ModBus RTU on RS485 port.

BATR R: integrated autonomous regulation.
BATR R010: integrated regulation for external 0-10V signal.

BATR R: integrated autonomous regulation

Operation

Duct blowing temperature regulation.
Room or return temperature regulation with or without supply air limit.
Minimum speed = 1.5 m / s - Maximum speed 10 m / s.
Need to control the heating to the operation of the fan.
Provide an MCR1 type time delay which delays the stopping of the fan to cool the pins.
Provide a contactor to cut off the power supply in the event of triggering of one of the safety thermostats
The contactor will be equipped with an auxiliary contact (NO/NC) to transfer the information to the regulation of the ventilation unit or to the BMS.

Construction

Body and IP44 box in aluzinc treated steel.
Connection by non-drilled flanges.
IP44 grommet to cut.
Heating elements shielded in stainless steel 304.
Safety thermostats with NC contact pre-wired in series, to be connected to an external power contactor:
1 safety thermostat with automatic reset 50°C.
1 safety thermostat with manual reset, set point 100°C.
2 LEDs indicating heating / operating mode-fault.

PID regulation

1 electronic power regulator type Triac.
1 safety air flow sensor.
1 TJK10K duct probe for measuring the supply air temperature or high and low limitation (+ 15 ° C / + 40 ° C).
1 box with NTC10 room sensor and TR5K (IP20) potentiometer with 0 to 30 ° C adjustment
- TR5K activated only if using the TJK10K duct probe to measure the supply air temperature
- TR5K + NTC10 activated if measurement in room + limitation in duct with TJK10K
ModBus RTU communication on RS485 port (setpoint temperature adjustment, alarms, etc.)

BATR R010: integrated regulation 0-10V external signal

Operation

In association with a Single or Double flow air handling unit delivering a 0-10V signal.
Minimum speed = 1.5 m / s - Maximum speed 10 m / s.
Need to control the heating to the operation of the fan.
Provide a time delay which delays the stopping of the fan to cool the pins.
Provide a contactor to cut off the power supply in the event of triggering of one of the safety thermostats
The contactor will be equipped with an auxiliary contact (NO/NC) to transfer the information to the regulation of the ventilation unit or to the BMS.

Construction

Body and IP44 box in Aluzinc treated steel.
Connection by non-drilled flanges.
IP44 grommet to cut.
Heating elements shielded in stainless steel 304.
Safety thermostats with NC contact pre-wired in series, to be connected to an external power contactor:
1 safety thermostat with automatic reset 50°C.
1 safety thermostat with manual reset, set point 100°C.
2 LEDs indicating heating / operating mode-fault

PID regulation

1 electronic power regulator type Triac.
1 safety air flow sensor.
ModBus RTU communication on RS485 port (alarms, ...).

B (mm)	H (mm)	L (mm)	Power (kW)
400	200	370	6 to 12
400	200	420	15
500	250	370	6 to 12
500	250	600	24
500	300	370	9 to 24
500	300	440	30
600	300	370	9 to 18
600	300	440	27
600	300	520	36
600	350	370	12 to 30
600	350	500	42
700	400	370	15 to 42
700	400	440	60
800	500	370	21 to 39
800	500	500	66
1000	500	370	24 to 45
1000	500	500	66