AIRLAM V2

Fresh air supply

On the front - Multiblades

View larger

AIRLAM V2

Fresh air supply

On the front - Multiblades

Neat aesthetics, anodized aluminum finish
Standard version and reinforced insulation version
Possibility of door installation

Application

Intended for the supply of natural smoke extraction air in public buildings, collective housing (premises, stairwells and circulation) and high-rise buildings.
Remote controlled Safety Actuated Device (DAS) intended for the introduction of fresh air into the exterior facade of the building (vertical facade only).
The opening is closed in the standby position and opens in the event of a fire to allow the introduction of the new air required for smoke extraction.

Collective residential buildings

Tertiary buildings

Description
Dimensions
Documentation
Public Price
Software
References

2 versions available:

standard version,
IS version: reinforced insulation.

Dimensions WxH:

Width: 330, 475, 600, 725, 850, 975, 1100, 1225 and 1350 mm,
Height: 350, 475, 600, 725, 850, 975, 1100, 1225 and 1350 mm.

Free area up to 130 dm2.
Electromagnetic tripping by 24Vdc or 48Vdc shunt or break coil. Actuation by pneumatic cylinder also possible.
Manual reset by handle.
Motorized reset by 24 Vdc electric cylinder for openings with a height H≥600 mm as an option (requires a reset box with 1, 2, 4 or 8 motors).
The interior trim grilles (GFAA, GAAA, GPAA) provide a uniform appearance with the trim grilles of the AVANTAGE range shutters.

Construction

Frame and horizontal slats in aluminum with natural anodized finish, painted finish in RAL color on request.
Slat clearance of 140 mm towards the outside of the building.
2 to 10 movable blades depending on the dimensions of the air intake.
Air supply with blades held closed in the standby position by an electromagnetic coil.
Opening by tripping of the 24 or 48Vdc shunt or break coil. The spool releases the blades which open thanks to the trigger mechanism (spring driven linkage located at the back of the blades).
Manual reset using a reset lever integrated into the air supply.
Electrical reset possible as an option for openings whose height H ≥ 600 mm.
Electric reset using a 24 Vdc linear actuator fixed to the linkage. Systematically provide a reset box (1, 2, 4, 8 motors) so that passage to the safety position (opening of the slats) takes priority over any other command (NC) and to allow electrical resetting of the AIRLAM (return in standby position).
EPDM rubber seals between the slats and vertical brush seals between the frame and the ends of the slats.
Insulated version (AIRLAM IS): slats reinforced insulation with M1 expanded polystyrene lining, 23 mm thick, enclosed in a PVC box.
Unipolar (FDCU) or bipolar (FDCB) start and end of run position contact.

GFAA, GAAA, GPAA dressing grid

Dimensions 330x600 to 1350x1100.
Free area greater than 90%.
GFAA: Fixed core grille - welded to the frame.
GAAA: Removable core grid - spring system.
GPSA: Removable core grid - spring system with fireman's square safety cam lock.
Painted finish in RAL color: consult us.
Frame and fin in natural-coloured anodized aluminium.
Fixing of the grid frame directly on the masonry wall using 4 screws (Ø3.5mm) not supplied. The fixing holes are located on the inside pleat return.
Blades with rounded profile inclined at 45° - crimped on aluminum tubes at the rear of the grille.

Facility

Allow 120 mm minimum for the passage of the lever on the interior side.
Installation in the lower part of the room.
Slat travel of 140 mm towards the outside of the building.
Use of counter-frame strongly recommended.
Installation of fins horizontally.
Reminder: all of the elements involved in rearming (handle to handle and attachment system) must be at a height of less than 2.5 m from the ground, to allow access.

Vertical section
AIRLAM-cpeV-dim